THIS PRODUCT IS 100% tested, certified and awarded the Australian Water Mark Standard [∼467 KB PDF].
Australian plumbing codes require the water mark approval before a water filtration product can be installed by a licensed plumber in your home. Our products give peace of mind to the consumer knowing their system and all components will comfortably withstand Australian Mains Water pressure.
Unfortunately numerous consumers have reported suffering varying degrees of flood damage to their homes and the inconvenience associated with it by purchasing cheap non watermark approved water filters on the internet.
Our systems are guaranteed to remove from your tap water the contaminants we claim as verified by independent test reports from certified laboratories.
2.Every system we sell is hand built and tested in Sydney in compliance with Australian water mark standards from American, British and Australian components.
3.With so many years of experience we have every confidence in providing you and your family the best available in water filtration technologies.
This ensures the following:
*Best plastics guaranteed 100% BPA free
*Highest bursting pressure (90PSI)
*Highest possible standards
Recomended Retail on this product is $995.00
SPECIAL HAS BEEN UPDATED TO GIVE YOU A CHOICE OF TWO DIFFERENT CARBON FILTER MEDIA'S...
1) HIGHGRADE CARBON- 0.5 MICRON:
-CAN BE USED ON ANY WATER TYPE, SUITED FOR TANK AND TOWN WATER SUPPLY , REMOVES HEAVY METALS IN ADDITION TO CYSTS (LIKE GIARDIA AND CRYPTOSPORIDIUM) , TASTE, COLOUR AND ODOUR...
2) GRANULAR ACTIVATED COCONUT CARBON/SILVER IMPREGNATED FILTER:
-CAN ALSO BE USED ON ANY WATER SUPPLY.. REMOVES (CHLORINE, TASTE , COLOUR, ODOUR, BUT WILL NOT REMOVE CYSTS) SHOULD NEVER BLOCK PREMATURELY...
This is the HIGH-RANGE, HIGH-FLOW whole house system. Designed for HIGH use it includes a twin 20" x 4.5" system, a sediment filter, and a 0.5 micron carbon filter that removes taste, colour, odour, PARASITES AND HEAVY METALS. Also included is the mounting Bracket. For removal of chlorine, taste, colour, odour, giardia and cryptosporidium cysts, lead and metals...
The high grade filter is our top of the range cartridge and remains the leading filter media in Australia. The filter is made in the states and has the highest possible American certification (nsf). This filter will remove greater then 99% of giardia and cryptosporidium (a common yet harmful bacteria) as wellas greater then 97% of lead which comes from your brass and copper pipes. Also removes chlorine taste colour and odour and other metals. A1 choice the best of the best.The high grade filter is our top of the range cartridge and remains the leading filter media in Australia. The filter is made in the states but has the highest possible American certification (nsf). This filter will remove greater then 99% of giardia and cryptosporidium (a common yet harmful bacteria) as well as greater then 99% of lead which comes from your brass and copper pipes. Also removes chlorine taste colour and odour and other metals. A1 choice the best of the best.M A T R I K X ® P b 1 E X T R U D E D F I L T E R S Multi-function Filter Soluble and insoluble lead reduction Powerful activated carbon filter 99.96%+ reduction of 1-2 μm particles High dirt capacity sediment filter MATRIKX® Pb1 HEAVY METALS REDUCTION MATRIKX® Pb1 extruded carbon filters reduce soluble lead using a powerful ion-exchange filter medium with high specificity for soluble lead. Particulate filtration is used to intercept insoluble lead-containing particles, even those less than 2μm in diameter. Standard filters* reduce lead (meeting National Sanitation Foundation Standard 53 test protocol) for over 2,500 gallons when operated at a flow of 0.75 GPM. CHEMICAL ADSORPTION MATRIKX® Pb1 filters offer high levels of organic chemicals reduction, and reduce trihalomethanes (THMs), volatile organic chemicals (VOCs), chlorine, and chemicals that contribute to taste and odor. PARTICULATE, CYST AND TURBIDITY REDUCTION MATRIKX® Pb1 filters provide ≥99.984% reduction of 3 - 4 μm particles (≥99.96% reduction of 1 -2 μm particles) and operate as high performance sediment filters with extended life. Graded-density prefiltration combined with a high dirt capacity extruded activated carbon serve to provide several times greater dirt life than molded filter products. DESIGN FEATURES MATRIKX® Pb1 filters flow in the radial (outside-to-inside) direction, providing increased dirt capacity and low pressure drop. Unlike granular activated carbon (GAC) filters, MATRIKX® Pb1 cartridges will not channel or bypass, due to the extreme uniformity of their extruded activated carbon core. Service life of the MATRIKX® Pb1 filter is greatly extended by two layers of prefiltration media consisting of a 15 μm polypropylene spunbonded outer prefiltration layer and a 5μm polypropylene melt-blown inner layer. Recommended installations are in fluids having upstream 1-5 μm prefilters or as stand-alone high-performance filter elements. APPLICATIONS MATRIKX® Pb1 is a powerful, multi-functional, filter cartridge for residential and industrial water purification systems, industrial effluent water treatment, food service, and industrial makeup, product rinse, and process water treatment. *A “standard filter” is 2.50” O.D. x 9.75” length and fits most standard household and commercial filter housings. FEATURES: Mixture of fine-mesh granular carbons and ultra-micronized ion-exchange filtration medium in high-integrity extruded structure. 99.984%+ reduction of 3 - 4 μm particulates. 99.96%+ reduction of 1 - 2 μm particulates. Graded-density prefiltration design. Manufactured using FDA-compliant materials. BENEFITS: Efficient reduction of soluble lead. High chemical adsorptive capacity. No channeling/ no fluidizing/ no bypassing. High TOC reduction. Eliminates release of carbon fines. Efficient reduction of insoluble lead particles. Cyst reduction: Giardia lamblia, Cryptosporidium. Effective turbidity reduction. Meets NSF Standard 42 Class 1 filtration standards. Maximum service life, resistance to fouling. Lowest extractables, pure materials of construction. P b 1 E X T R U D E D F I L T E R S SOLUBLE LEAD REMOVAL Test Results: Standard 2.50” O.D. x 1.25” I.D. x 9.75” L MATRIKX® Pb1 extruded carbon filter cartridges were challenged with influent water flowing at 0.75 GPM and containing approximately 150 ppb of soluble lead at both high pH and alkalinity, and low pH and low alkalinity. The results demonstrate that the MATRIKX® Pb1 will reduce soluble and insoluble lead to below 15 ppb for greater than 2,500 gallons. Test Conditions: Two randomly selected, standard production cartridges were challenged with water containing an average of 150 ppb of soluble lead nitrate at a flow rate of 0.75 GPM to determine the filter’s efficiency for the reduction of soluble lead at low pH, TDS and alkalinity. A second set of filters were tested under similar conditions, but with influent water at high pH, high TDS and alkalinity. Flow rate: 0.75 GPM System pressure: 60 psig Operating cycle: 50% on / 50% off Influent water analysis: Low Ph High Ph Alkalinity 30mg/L 210 mg/L pH 6.7 8.3 TDS 144 mg/L 284 mg/L Turbidity <0.1 NTU <0.1 NTU Temperature: 20º C. 20º C. Hardness: 24 mg/L 120 mg/L Polyphosphate: <0.05 mg/L <0.05 mg/L Source of test data: Spectrum Laboratories, New Brighton, Minnesota. CHLORINE REDUCTION Test Results: Standard 2.50” O.D. x 1.25” I.D. x 9.75” L MATRIKX® Pb1 extruded carbon filters removed all detectable free chlorine (<0.1 ppm) from an influent challenge containing an average of 2.0 ppm free chlorine flowing at 0.75 GPM, and maintained this level of performance for 2,500 gallons. Test Conditions: Two randomly selected, standard production cartridges were evaluated for chlorine reduction. Flow rate: 0.75 GPM System pressure: 60 psig Operating cycle: 50% on / 50% off Chlorine challenge: 2 -2.5 ppm FAC (free available chlorine). Total challenge: 2,500 gallons Influent water analysis: pH . . . . . . . . . . 7.5 TDS . . . . . . . . . 280 mg/L Turbidity . . . . . . <0.1 NTU Temperature . . . 20º Celsius Source of test data: Spectrum Laboratories, New Brighton, Minnesota. FLOW RESISTANCE Test Results: Standard MATRIKX® Pb1 extruded carbon filter cartridges were tested with municipal tap water from Bridgeport, CT, at 60 psig system pressure, to determine differential-pressure vs. flow curves. The standard 2.50” O.D. x 9.75” L MATRIKX® Pb1 filter has a ΔP= 4.00 psid at 1.0 GPM flow. Test Conditions: Three randomly selected, standard production cartridges were subjected to varying flows to determine the initial-differential-pressure vs. flow curve. Influent water: Bridgeport, CT municipal drinking water pH of Influent water: 6.5 Temperature: 20º C System pressure: 60 psig, constant Range of tested flows: 1 - 10 GPM. Instrumentation: Omega Engineering FL710 Series, 1 to 11 GPM range, with 0.2 GPM accuracy Source of test data: KX Industries L.P., Bridgeport, CT PARTICULATE, CYST AND TURBIDITY REDUCTION Test Results: Standard 2.50” O.D. x 1.25” I.D. x 9.75” L MATRIKX® Pb1 extruded carbon filters were evaluated for particulate reduction using in-line particle counting instruments, and demonstrated ≥99.984% reduction at 3-4 μm particles (≥99.96% reduction at 1 - 2 μm particles) which exceeds the current NSF requirement for cyst and turbidity reduction under NSF Standard 53. Test Conditions: Instrumentation: HIAC ROYKO 8000A, automatic particle counter. Sensor: LD 400 Influent water temperature: 20º C. Challenge: Fine test dust Flow rate: 4.0 GPM Source of test data: Inter Basic Resources, Inc. Ann Arbor, Michigan. NOTES: 1Performance of a given MATRIKX® extruded carbon filter varies in direct proportion to the total weight of carbon in each filter. For example, a 4.25” O.D. x 20” L MATRIKX® filter contains approximately seven times as much activated carbon as a 2.50” O.D. x 9.75” L MATRIKX® filter, and will therefore have seven times the rated chlorine and lead absorption capacities, when operating at seven times the rated flow of the smaller cartridge. Hence, rated flow is based on maintaining identical contact/residence times for all filters. 2Chlorine capacity is the estimated capacity in gallons during which the filter will remove greater than 95% of influent chlorine (2ppm) when operating at a given flow. 3Particulate rating for >99.9% removal of a given size as determined from particle counting results. 4Lead reduction capacity in gallons to obtain ≥90% removal of influent lead (150 ppb influent) at a given flow and at a pH of 6.5/8.5, according to the standard National Sanitation Foundation protocol. WARNINGS: Maximum Operating Temperature: 125º F. Maximum Operating Pressure: 250 psig. Maximum Differential Pressure: 100 psid. Collapse Pressure: 200 psid. MATRIKX® filters are not to be autoclaved or steam sterilized. Use MATRIKX® carbon filters only with microbiologically safe water. Activated carbon filters are not designed to kill or remove bacteria or viruses. Actual results obtained will vary with various combinations and amounts of organic contaminants, changes in pH or other conditions encountered in actual use. All information presented here is based on data believed to be reliable. It is offered for evaluation and verification, but is not to be considered a warranty of any kind. MATRIKX® filters are designed to fit most standard household and commercial or industrial housings. Call KX Industries to check filter housing compatibility. ORDERING INFORMATION: MATRIKX® Pb1 Extruded Carbon Filters Part Number Outer Diameter Length 06-250-125-050 2.50” 5.00” 06-250-125-975 2.50” 9.75” Standard filters are finished with an outer polypropylene spunbonded prefiltration medium. A protective polypropylene netting is applied to the exterior of the cartridge. Polypropylene end caps with compression gaskets fit most standard housings. Inquire concerning alternative filter finishing options, including alternative end cap and housing interface styles, a wide range of non-standard extruded filter sizes, and non-standard prefiltration systems. This product is made in accordance with or covered under one or more of the following United States patents: 5,019,311; 5,147,722; 5,189,092; 5,249,948; 5,331,037; 5,922,803; 5,946,342; 6,061,384 and corresponding patents in other countries. ©2002 KX Industries, L.P. All rights reserved. The KX Logo, MATRIKX®, and “Genuine Part Number O.D. x Length Filter Chlorine capacity Absolute μm Lead Reduction Initial ΔP Weight1 @ Flow2 Rating3 Capacity @ Flow4 @ Flow 06-250-125-975 2.50” x 9.75” 0.85 lb. >6,000 gal. @ 0.75 GPM 1-2 μm 2,500 gal. @ .75 GPM 4.0 psid @ 0.75 GPM 06-250-125-20 2.50” x 20” 1.90 lb. >12,000 gal. @ 1.5 GPM 1-2 μm 5,000 gal. @ 1.5 GPM 4.0 psid @ 1.50 GPM 06-425-200-975 4.25” x 9.75” 3.20 lb. >20,000 gal. @ 2.5 GPM 1-2 μm 8,000 gal. @ 2.5 GPM 7.0 psid @ 2.50 GPM 06-425-200-20 4.25” x 20” 6.60 lb. >42,000 gal. @ 5.0 GPM 1-2 μm 17,000 gal. @ 5.0 GPM 6.5 psid @ 5.00 GPM TABLE 1: SUMMARY TECHNICAL DATA Part Number Outer Diameter Length 06-425-200-975 4.25” 9.75” 06-250-200-20 4.25” 20.00” Special Order 1’ to 6” 1” to 60”